Как посмотреть серийный номер cisco

Cisco switch/router (commands to find model and serial number)

Sometimes it is needed to collect inventory information from Cisco switch or router like serial number and model. It is especially helpful when you have only access to that device remotely.

• access by ssh or telnet to Cisco switch or router
• an account with required privileges or maximum possible privileges (level 15)

Historically, you would use the following command, but in modern Cisco IOS releases, there is no way to get model and serial number like it was before:

There is a solution. The following commands definitely give you mode and serial number information:

PS UDI means Unique Device Identifier. Consist of Product ID and Serial Number.

How to get Chasis Serial Number on a Cisco Catalyst Switch

In Cisco Catalyst switches running Cisco IOS, you can find the serial numbers using the following commands on the various models:

Catalyst 6509 switch:

Switch1#show idprom backplane
IDPROM for backplane #0
(FRU is 'Catalyst 6500 6-slot backplane')
OEM String = 'Cisco Systems'
Product Number = 'WS-C6506'
Serial Number = 'TBAxxxxxxxx'
Manufacturing Assembly Number = '73-3436-01'
Manufacturing Assembly Revision = 'A0'
Hardware Revision = 1.0
Current supplied (+) or consumed (-) = -A

On a Catalyst 4500/4000 switch,

Switch1#show idprom chasis
Chassis Idprom :
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 4081
Idprom Size = 256
Block Count = 2
FRU Major Type = 0x4001
FRU Minor Type = 37
OEM String = Cisco Systems, Inc.
Product Number = WS-C4506
Serial Number = XXXXXXXXXXX
Part Number = 73-8107-04
Part Revision = 01
Manufacturing Deviation String = 0
Hardware Revision = 0.4
Manufacturing Bits = 0x0000
Engineering Bits = 0x0000
Snmp OID = 0.0.0.0.0.0.0.0
Power Consumption = 0
RMA Failure Code = 0 0 0 0
Chassis Block Signature = 0x4001
Chassis Block Version = 1
Chassis Block Length = 22
Chassis Block Checksum = 628
Feature Bits = 0x0000000000000000
MAC Base = 000a.4172.df40
MAC Count = 64

Switch Uptime : 1 hour, 29 minutes
Base ethernet MAC Address : 00:0D:29:B4:3F:00
Motherboard assembly number : 73-7055-06
Power supply part number : 341-0034-01
Motherboard serial number : CAT07260438
Power supply serial number : PHI0708008X
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C3750-24TS-E
System serial number : CATXXXXXXXX

Switch1#show hardware
…
…
…
IDPROM Contents :
FRU Type : 0x0.0x0
OEM String : Cisco_Systems
Product Number : WS-C2948G-L3
Serial Number : FOX05330ADH
Mfg. Assembly No. : 73-4083-07
Mfg. Assembly Ver. : A0
Hardware Version : 1.7
FPGA Version : 0
SNMP IOD : 9.5.1.3.1.1.2.275
RMA Code : 0
Feature Bits : 0x00000000
MAC Address Base : 00:07:85:07:DC:00
Total MAC Addrs. : 1024

Cisco Catalyst 4500/4000 switch:

Switch1#show idprom chasis
Chassis Idprom :
Common Block Signature = 0xABAB
Common Block Version = 1
Common Block Length = 144
Common Block Checksum = 4081
Idprom Size = 256
Block Count = 2
FRU Major Type = 0x4001
FRU Minor Type = 37
OEM String = Cisco Systems, Inc.
Product Number = WS-C4506
Serial Number = XXXXXXXXXXX
Part Number = 73-8107-04
Part Revision = 01
Manufacturing Deviation String = 0
Hardware Revision = 0.4
Manufacturing Bits = 0x0000
Engineering Bits = 0x0000
Snmp OID = 0.0.0.0.0.0.0.0
Power Consumption = 0
RMA Failure Code = 0 0 0 0
Chassis Block Signature = 0x4001
Chassis Block Version = 1
Chassis Block Length = 22
Chassis Block Checksum = 628
Feature Bits = 0x0000000000000000
MAC Base = 000a.4172.df40
MAC Count = 64

Catalyst 3750/3760/3550/2950/2970/2940/2900XL/3500XL:

Switch Uptime : 1 hour, 29 minutes
Base ethernet MAC Address : 00:0D:29:B4:3F:00
Motherboard assembly number : 73-7055-06
Power supply part number : 341-0034-01
Motherboard serial number : CAT07260438
Power supply serial number : PHI0708008X
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C3750-24TS-E
System serial number : CATXXXXXXXX

Catalyst 2948GL3/4908G-L3/4980G-L3:

Switch1#show hardware
…
…
…
IDPROM Contents :
FRU Type : 0x0.0x0
OEM String : Cisco_Systems
Product Number : WS-C2948G-L3
Serial Number : FOX05330ADH
Mfg. Assembly No. : 73-4083-07
Mfg. Assembly Ver. : A0
Hardware Version : 1.7
FPGA Version : 0
SNMP IOD : 9.5.1.3.1.1.2.275
RMA Code : 0
Feature Bits : 0x00000000
MAC Address Base : 00:07:85:07:DC:00
Total MAC Addrs. : 1024

Catalyst 8510/8540:

If you’re new here, you may want to subscribe to my RSS feed. Thanks for visiting!

Как посмотреть серийный номер cisco

brianwhelton

• Facebook Opens a new window
• Twitter Opens a new window
• Reddit Opens a new window
• LinkedIn Opens a new window

Brian Whelton

Cisco: How to determine the serial number of hardware components

Some days ago I had to check for the serial number of a faulty fan tray that need to be exchanged in C6500 series. Now most of you I believe know the commands “show version” or “show hardware” which will get all the information that you need most of the time, but not always. I decided to put in this post some useful commands to identify the Cisco hardware components and their respective identifiers (serial nnumber) on different platforms.

I will use for my example a C6500 series switch, because this support most of the commands that I know. Also the real serial numbers will be stripped out and replace with a fake one, as I don’t want this to be used by third parties.

show version – Any network administrators who work with Cisco devices are more than likely familiar with the show version command. The most common use of this command is to determine which version of the Cisco IOS a device is running, but this command also offers different usesful information like the IOS version, ROM bootstrap, uptime, RAM quantity, FLASH capacity and many more. Coming back to our topic from this post, show version ouput the Processor board ID which should be the same serial number like the one printed on a sticker on the back of the Cisco device. This is also used as the device serial number in any service contract that you might have. You can see below an excerpt of the show version command on C6500 platform:

Cisco Internetwork Operating System Software
IOS ™ s72033_rp Software (s72033_rp-JK9SV-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 17-Aug-05 17:48 by evmiller
Image text-base: 0x4002100C, data-base: 0x42698000

ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-JK9SV-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1)

r8-c6500 uptime is 6 weeks, 3 days, 20 hours, 32 minutes
Time since r8-c6500 switched to active is 6 weeks, 3 days, 20 hours, 31 minutes
System returned to ROM by reload at 18:50:17 PDT Sat Apr 7 2007 (SP by reload)
System image file is “disk0:s72033-jk9sv-mz.122-18.SXD6.bin”

If you require further assistance please contact us by sending email to
[email protected]

cisco WS-C6506 (R7000) processor (revision 3.0) with 458720K/65536K bytes of memory.
Processor board ID SAL00000XXX
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 Virtual Ethernet/IEEE 802.3 interface(s)
42 Gigabit Ethernet/IEEE 802.3 interface(s)
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102

show module – beside giving you a list of the modules and slots where they are connected (e.g. on C6500 series), it also return status, model, hardware address, software / hardware version and the most important for us today, the serial number of each module / sub-module. Check C6500’s output of show module command:

Mod Ports Card Type Model Serial No.
— —– ————————————– —————— ———–
1 0 FRU type (0x6003, 0x450(1104)) 7600-SSC-400 JAB000000XX
2 2 IPSec VPN Accelerator WS-SVC-IPSEC-1 SAD0000X0X
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516-GBIC SAL0000000
4 6 Firewall Module WS-SVC-FWM-1 SAD000000X
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL0000XX00
6 16 SFM-capable 16 port 1000mb GBIC WS-X6516-GBIC SAL0000XXXX

Mod MAC addresses Hw Fw Sw Status
— ———————————- —— ———— ———— ——-
1 0013.60a4.c688 to 0013.60a4.c6c7 1.0 Unknown Unknown PwrDown
2 0001.c9df.65ba to 0001.c9df.65bd 1.3 Unknown Unknown PwrDown
3 0009.11e3.1c84 to 0009.11e3.1c93 5.0 Unknown Unknown PwrDown
4 0019.5671.803a to 0019.5671.8041 4.0 7.2(1) 3.2(10) Ok
5 0013.c347.2e90 to 0013.c347.2e93 5.3 8.4(2) 12.2(18)SXD6 Ok
6 000d.65f7.1a8c to 000d.65f7.1a9b 5.5 6.3(1) 8.3(0.156)RO Ok

Mod Sub-Module Model Serial Hw Status
— ————————— —————— ———— ——- ——-
5 Policy Feature Card 3 WS-F6K-PFC3B SAL0000XXX 2.3 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL0000X0X0 2.6 Ok

Mod Online Diag Status
— ——————-
1 Unknown
2 Unknown
3 Unknown
4 Pass
5 Pass
6 Pass

show inventory – retrieve and display the Unique Device Identifier (UDI) information from any Cisco product that has electronically stored such identity information. A UDI consists of the following elements: Product identifier (PID), Version identifier (VID) and Serial number (SN).
The PID is the name by which the product can be ordered; it has been historically called the “Product Name” or “Part Number.” This is the identifier that one would use to order an exact replacement part.

The VID is the version of the product. Whenever a product has been revised, the VID will be incremented. The VID is incremented according to a rigorous process derived from Telcordia GR-209-CORE, an industry guideline that governs product change notices.

The SN is the vendor-unique serialization of the product. Each manufactured product will carry a unique serial number assigned at the factory, which cannot be changed in the field. This is the means by which to identify an individual, specific instance of a product.

The raw parameter on the show inventory command is useful mostly for troubleshooting purpose. Compared with the previous commands, this one give you a better overview of the full range of hardware components installed (e.g. fan-tray, power source….) Below you can see an excerpt from the command output:

NAME: “WS-C6506”, DESCR: “Cisco Systems Catalyst 6500 6-slot Chassis System”
PID: WS-C6506 , VID: , SN: SAL00000XXX

NAME: “WS-C6K-VTT 1”, DESCR: “VTT FRU 1”
PID: WS-C6K-VTT , VID: , SN: SMT0000X000

NAME: “WS-C6K-VTT 2”, DESCR: “VTT FRU 2”
PID: WS-C6K-VTT , VID: , SN: SMT0000X000

NAME: “WS-C6K-VTT 3”, DESCR: “VTT FRU 3”
PID: WS-C6K-VTT , VID: , SN: SMT0000X000

NAME: “WS-C6000-CL 1”, DESCR: “C6K Clock FRU 1”
PID: WS-C6000-CL , VID: , SN: SMT0000X000

NAME: “WS-C6000-CL 2”, DESCR: “C6K Clock FRU 2”
PID: WS-C6000-CL , VID: , SN: SMT0000A000

NAME: “1”, DESCR: “7600-SSC-400 0 ports FRU type (0x6003, 0x450(1104)) Rev. 1.0”
PID: 7600-SSC-400 , VID: V01, SN: JAB000000XX

show diagbus – in order to find the serial number of port adapters that plug into the Flex WAN module, issue the show diagbus command from the MSFC command-line interface (CLI), like in the example below:

Slot 2: Logical_index 4
2 port adapter Enhanced FlexWAN controller
Board is analyzed ipc ready
HW rev 2.0, board revision A0
Serial Number: JAB0000000 Part number: 73-9539-03

Slot database information:
Flags: 0x2004 Insertion time: 0x249E4 (18w3d ago)

Controller Memory Size:
192 MBytes CPU Memory
63 MBytes Packet Memory
255 MBytes Total on Board SDRAM
Cisco IOS Software, cwlc Software (cwpa2-DW-M), Version 12.2(33)SXH3a, RELEASE SOFTWARE (fc1)

PA Bay 0 Information:
T3+ Serial PA, 1 ports
EEPROM format version 1
HW rev 1.00, Board revision B1
Serial number: 15225203 Part number: 73-3762-02
Slot 2: Logical_index 5
2 port adapter Enhanced FlexWAN controller
Board is analyzed ipc ready
HW rev 2.0, board revision A0
Serial Number: JAB0000000 Part number: 73-9539-03

Slot database information:
Flags: 0x2004 Insertion time: 0x209C0 (18w3d ago)

Controller Memory Size:
192 MBytes CPU Memory
63 MBytes Packet Memory
255 MBytes Total on Board SDRAM
Cisco IOS Software, cwlc Software (cwpa2-DW-M), Version 12.2(33)SXH3a, RELEASE SOFTWARE (fc1)

show idprom – In order to determine the serial number for the chassis and other components. This command has multiple parameter to issue in case that you want to restrict the information that is returned to you show idprom [parameter]. Some parameter option would be: backplane, fan-tray, module, interface and others which you can discover with well known help command show idprom ? . An example you can see below:

show idprom backplane
IDPROM for backplane #0
(FRU is ‘Catalyst 6500 6-slot backplane’)
OEM String = ‘Cisco Systems’
Product Number = ‘WS-C6506’
Serial Number = ‘SAL0000XXX’
Manufacturing Assembly Number = ’73-3436-03′
Manufacturing Assembly Revision = ‘B0’
Hardware Revision = 3.0
Current supplied (+) or consumed (-) = –

As i said before not all of this commands are working on every Cisco device, that’s why I choose a C6500 for the example as it support all of them. Also this are the commands that I used mostly to obtain information about Cisco hardware components, if there are another ones that you find useful please add them to the comments section and I’ll add them to this article.